Copper and zinc adsorption from bacterial biomass - possibility of low-cost industrial wastewater treatment.

The increasing interest of all stakeholders to achieve environmental protection with socioeconomic development puts pressure on industrial processes for less negative impact on the environment. The use of biomass for wastewater treatment has increased due to its low costs and technical feasibility. The present study aimed the use of biomass from a waste of known polluted area for the adsorption of Zn and Cu in a fixed-bed reactor. Samples were collected in Cubatão (Brazil) and cultivated in LB medium. Resulting cultivable bacterial communities were identified as Enterococcus faecalis and Pseudomonas aeruginosa. Adsorption experiments were performed varying the metallic ion concentration and the amount of biomass. Adsorption experiments showed efficiency rates up to 90%. As the concentration of metallic ions increased, the adsorption efficiency decreased, indicating that the active sites were saturated. Activated charcoal demonstrated lower adsorption rates than biomass. Elution process showed that HNO3 had better efficiency than HCl. Zn adsorption fitted better for Lineweaver-Burk model (Qmax = 200 mg/g of biomass), while Cu adsorption fitted better for Langmuir model (Qmax = 164 mg/g of biomass). Results here demonstrated that the adsorption of Zn and Cu simulating an industrial wastewater by the biomass from a contaminated area is technically feasible.

Characterization of end-of-life LEDs: Mapping critical, valuable and hazardous elements in different devices.

LEDs are essential components in the vast majority of technologies. Over the years, to maintain the comfort of modern life, an increase in the generation of LED waste has been observed. It is known that LED wastes are potential sources for recovering critical, valuable, and rare earth metals. Therefore, this study aims to provide a complete characterization of LED models: cold white (CW), warm white (WW), and RED, mapping potential elements to be recovered and hazardous elements to the environment and public health. The LED models were analyzed by ICP-OES, SEM-EDS, and FTIR-ATR. It was observed in WW a higher concentration of Ce, Ga, and Y than in CW and RED due to its greater density of phosphor particles in the encapsulant material. In, Ga, Ag, and Au were seen in LED dies of WITHES, while As, and Ga were identified in RED LED dies. Pb was observed in the solder of CW and RED. LEDs' encapsulant and polymeric structures are polydimethylsiloxane (PDMS) and polyamide 11, respectively. The study findings showed a wide variation in metal contents and distribution regarding different LED models. Those variations were pointed out, providing opportunities for developing future works aimed at recycling and treating LED waste.

Potential Application of Alternative Materials for Organic Pollutant Removal.

The work aims to synthesize and characterize vegetal charcoal (or biochar) from Syzygium cumini (AC-SC), evaluating the adsorption capacity for dexamethasone drug (DEX) removal, using the kinetic and equilibrium adsorption. The samples were characterized by N2 porosimetry, X-ray diffraction, scanning electron microscopy with energy-dispersive spectroscopy, zeta potential, and zero charge point. Adsorption equilibrium was carried out applying the Langmuir, Freundlich, Redlich-Peterson, Sips, and Toth models, and kinetic adsorption applied the pseudo-first order, pseudo-second order, Elovich, Avrami, and Weber-Morris models. AC-SC showed a heterogeneous and porous surface, negatively charged, crystalline structure, specific surface area of the 2.14 m2 g-1 and pHZCP = 7.36. About the effect of the AC-SC concentration, 5.0 g L-1 showed the best DEX removal (53.02%), about the others' concentration (2.0 and 7.5 g L-1). About the equilibrium and kinetic adsorption, the Sips model and pseudo-second order showed the best experimental data adjusted, indicating that the adsorption monolayer was dependent on the ions onto the biosorbent, with a maximum adsorption capacity of 0.744 mg g-1 after 180 min. Therefore, AC-SC can be used as an alternative material in the removal of organic pollutants, such as drug removal.

Adsorption for rhodamine b dye and biological activity of nano-porous chitosan from shrimp shells.

The present work aims to evaluate the removal capacity of Rhodamine B dye (RhB) using nano-porous chitosan (NC) from shrimp shells. NC was characterized by XRD, SEM-EDS, N2 porosimetry, zeta potential (ZP), FTIR, DLS, and zero charge point (pHZCP). Compound central rotational design (CCRD) was used to determine the ideal condition and antimicrobial activity was evaluated against different strains. NC showed characteristic of semi-crystalline material with negative charge surface (around - 21.13 mV), and SBET = 1.12 m2 g-1, Vp = 0.0064 cm3 g-1, Dp = 32.09 nm and pHZCP ≈ 7.98. Kinetic adsorption showed the pseudo first-order model had the best fit, with adsorption capacity (q1) between 3.78 and 64.43 mg g-1 and pseudo first-order kinetic constant (k1) between 0.066 and 0.052 min-1. Sips model best described the equilibrium data, with a maximum adsorption capacity of 505.131 mg g-1. Antimicrobial activity was observed at 0.25 mg mL-1 for different strains. Therefore, NC has potential application in the removal of the dye, combining sustainable development associated with nanotechnology.

Synthesis and characterization of nanozeolite from (agro)industrial waste for application in heterogeneous photocatalysis.

The pollution of wastewater with dyes has become a serious environmental problem around the world. In this context, the work aims to synthesize and characterize a supported nanocatalyst (NZ-180) from rice husk (RH) and alum sludge (AS) incorporating silver (AgNPs@NZ-180) and titanium nanoparticles (TiNPs@NZ-180) for Rhodamine B (RhB) dye degradation, under UV and visible irradiation. Central rotatable composite design (CRCD) was used to determine ideal conditions, using nanocatalyst and dye concentration such as input variables and degradation percentage like response variable. Samples were characterized by XRD, SEM-EDS, N2 porosimetry, DLS, and zeta potential analyses. TiNPs@NZ-180 showed the best photocatalytic activity (62.62 and 50.82% under UV and visible irradiation, respectively). Specific surface area has increased from 35.90 to 418.90 m2 g-1 for NZ-180 and TiNPs@NZ-180, respectively. Photocatalytic performance of TiNPs@NZ-180 has reduced to 8 and 10% after 5 cycles under UV and visible light irradiation. Ideal conditions found by CRCD were 2.75 g L-1 and 20 mg L-1 for nanocatalyst and RhB concentrations, respectively. Therefore, (agro)industrial waste present such an alternative material for application in the removal of wastewater with dyes, which helps in the reduction of the impact of chemicals/pollutants on human and animal health.

Green Nanoarchitectonics of Silver Nanoparticles for Antimicrobial Activity Against Resistant Pathogens.

Antimicrobial resistance represents a serious concern to public health, being responsible for hospital infections, affecting mainly immunosuppressed patients. Thus, nanotechnology appears as an alternative to solve this problem, through the application of metallic nanoparticles with antimicrobial activity. The present work aims to synthesize and characterize AgNPs from Klebsiella pneumoniae (AgNPs-KP) and Aloe vera extract (AgNPs-AV), evaluating the antimicrobial activity against Klebsiella pneumoniae carbapenemase (KpC) and the cytotoxicity in the L929 cell line. AgNPs were prepared by the biosynthetic method using Klebsiella pneumoniae and were characterized by XRD, FTIR and SEM-EDS. Antimicrobial activity was tested using the MIC and MBC. The cytotoxicity was evaluated by the MTT method and neutral red. The production of ROS and nitrogen RNS tests were performed in the L929 cell line. Thus, it was possible to confirm the production of AgNPs-KP, through morphological, structural and elemental analysis. AgNPs from Klebsiella pneumoniae had potent antimicrobial activity in low concentration against antimicrobial resistant pathogens with MIC 9.76 µg mL-1 and MBC 9.06 µg mL-1. Moreover, AgNPs-KP in concentrations of 10, 30 and 100 µg mL-1 did not show cytotoxic properties for the L929 fibroblast, where only the cytotoxic effect was observed in high concentrations (300 µg mL-1). AgNPs-KP did not produce ROS about the analyzed concentrations and RNS production was only in the highest concentration of 3000 µg mL-1. Therefore, AgNPs biosynthesized by Klebsiella pneumoniae have potential medical applicability as a promising antimicrobial agent, using a simple and low-cost method, correlating nanomedicine as nanostructured materials.

Silver nanoparticles from residual biomass: Biosynthesis, characterization and antimicrobial activity.

The industrial effluent contaminated with organic pollutants has been causing an increase in the toxicity of the ecosystem, causing a great environmental impact. Thus, the present work aims the green synthesis of silver nanoparticles (AgNPs) from Aloe vera, its characterization and antimicrobial activity against Pseudomonas aeruginosa (ATCC 27853) and Staphylococcus aureus (ATCC 25923). AgNPs were characterized by X-ray diffraction (XRD), Scanning Electronic Microscopy with Energy Dispersive Spectroscopy (SEM-EDS), Zeta Potential (ZP) and N2 porosimetry (BET/BJH method). Antimicrobial activity were carried out by Minimal Inhibitory Concentration (MIC) method. The XRD demonstrated characteristic peaks of AgNPs at 38.29°; 44.55° and 64.81°, and SEM-EDS micrographs showed that AgNPs produced by biomolecules of Aloe vera extract resulted in a weight concentration around 92.59% silver, 7.15% oxygen and 0.26% chlorine. Regarding zeta potential, all samples showed negative electric charge (around -35.3 mV), while N2 porosimetry resulted in a surface specific area of 6.09 m2 g-1, with a volume and diameter pore of 0.032 cm³ g-1 and 33.47, respectively. Antimicrobial activity was observed at 15.62 µg mL-1 and 31.25 µg mL-1 for P. aeruginosa and S. aureus, respectively. Thus, AgNPs can be considered a promising nanoparticle for degradation of organic pollutants in aqueous solution as well as an adjuvant for treatment of microbial infections.

Electric car battery: An overview on global demand, recycling and future approaches towards sustainability.

Li-ion batteries are daily present in our electronic devices. These batteries are used in electric and hybrid vehicles supporting the current agreements to decrease greenhouse gas emissions. As a result, the electric vehicle demand has increased in the world. As Li-ion batteries are composed of critical metals in which there is a risk of interruption of supply in the medium term, recycling is the key to a sustainable future without internal combustion vehicles. Understanding the current scenario and future perspectives is important for strategies of new battery design, recycling routes and reverse logistics, as well as policies for sustainable development. This paper presents an overview of current and future vehicles used worldwide. An increase from 1.3 to 2 billion vehicles is expected worldwide until 2030; an outstanding demand will occur mainly in BRICS countries. The data demonstrated a correlation between the number of vehicles in use and GDP. Patents and processes designed for recycling Li-ion batteries and the new developments on pyro-, hydro-, and bio-metallurgical routes have been revised. The manuscript describes the importance and benefits of recycling as regards the supply of critical metals and future trends towards a circular economy.

Investigation of ion-exchange membranes by means of chronopotentiometry: A comprehensive review on this highly informative and multipurpose technique.

Electrodialysis is mostly used for drinking water production but it has gained applicability in different new fields in recent decades. Membrane characteristics and ion transport properties strongly influence the efficiency of electrodialysis and must be evaluated to avoid an intense energy consumption and ensure long membrane times of usage. To this aim, conducting studies on ion transport across membranes is essential. Several dynamic characterization methods can be employed, among which, chronopotentiometry has shown special relevance because it allows a direct access to the contribution of the potential in different states of the membrane/solution system. The present paper provides a critical review on the use of chronopotentiometry to determine the main membrane transport properties and to evaluate mass transfer phenomena. Properties, such as limiting current density, electrical resistances, plateau length, transport number of counter-ions in the membrane, transition times, and apparent fraction of membrane conductive area have been intensively discussed in the literature and are presented in this review. Some of the phenomena evaluated using this technique are concentration polarization, gravitational convection, electroconvection, water dissociation, and fouling/scaling, all of them also shown herein. Mathematical and experimental studies were considered. New trends in chronopotentiometric studies should include ion-exchange membranes that have been recently developed (presenting anti-fouling, anti-microbial, and monovalent-selective properties) and a deeper discussion on the behaviour of complex solutions that have been often treated by electrodialysis, such as municipal wastewaters. New mathematical models, especially 3D ones, are also expected to be developed in the coming years.

Treatment of Cyanide-Free Wastewater from Brass Electrodeposition with EDTA by Electrodialysis: Evaluation of Underlimiting and Overlimiting Operations.

Growing environmental concerns have led to the development of cleaner processes, such as the substitution of cyanide in electroplating industries and changes in the treatment of wastewaters. Hence, we evaluated the treatment of cyanide­free wastewater from the brass electroplating industry with EDTA as a complexing agent by electrodialysis, aimed at recovering water and concentrated solutions for reuse. The electrodialysis tests were performed in underlimiting and overlimiting conditions. The results suggested that intense water dissociation occurred at the cathodic side of the commercial anion­exchange membrane (HDX) during the overlimiting test. Consequently, the pH reduction at this membrane may have led to the reaction of protons with complexes of EDTA-metals and insoluble species. This allowed the migration of free Cu2+ and Zn2+ to the cation-exchange membrane as a result of the intense electric field and electroconvection. These overlimiting phenomena accounted for the improvement of the percent extraction and percent concentration, since in the electrodialysis stack employed herein, the concentrate compartments of cationic and anionic species were connected to the same reservoir. Chronopotentiometric studies showed that electroconvective vortices minimized fouling/scaling at both membranes. The electrodialysis in the overlimiting condition seemed to be more advantageous due to water dissociation and electroconvection.

E-waste management and sustainability: a case study in Brazil.

The advancement of technology and development of new electronic and electrical equipment with a reduced life cycle has increased the need for the disposal of them (called Waste of Electric and Electronic Equipment or simply e-waste) due to defects presented during use, replacement of obsolete equipment, and ease of acquisition of new equipment. There is a lack of consumer awareness regarding the use, handling storage, and disposal of this equipment. In Brazil, the disposal of post-consumer waste is regulated by the National Solid Waste Policy, established by Law No. 12305 and regulated on the 23rd December 2010. Under this legislation, manufacturers and importers are required to perform a project for the Reverse Logistics of e-waste, though its implementation is not well defined. This work focuses on the verification of the sustainability of reverse logistics suggested by the legislation and the mandatory points, evaluating its costs and the possible financial gain with recycling of the waste. The management of reverse logistics and recycling of waste electrical and electronic equipment, or simply recycling of e-waste, as suggested by the government, will be the responsibility of the managing organization to be formed by the manufacturers/importers in Brazil.

Recycling of WEEE: characterization of spent printed circuit boards from mobile phones and computers.

This paper presents a comparison between printed circuit boards from computers and mobile phones. Since printed circuits boards are becoming more complex and smaller, the amount of materials is constantly changing. The main objective of this work was to characterize spent printed circuit boards from computers and mobile phones applying mineral processing technique to separate the metal, ceramic, and polymer fractions. The processing was performed by comminution in a hammer mill, followed by particle size analysis, and by magnetic and electrostatic separation. Aqua regia leaching, loss-on-ignition and chemical analysis (inductively coupled plasma atomic emission spectroscopy - ICP-OES) were carried out to determine the composition of printed circuit boards and the metal rich fraction. The composition of the studied mobile phones printed circuit boards (PCB-MP) was 63 wt.% metals; 24 wt.% ceramics and 13 wt.% polymers; and of the printed circuit boards from studied personal computers (PCB-PC) was 45 wt.% metals; 27 wt.% polymers and ceramics 28 wt.% ceramics. The chemical analysis showed that copper concentration in printed circuit boards from personal computers was 20 wt.% and in printed circuit boards from mobile phones was 34.5 wt.%. According to the characteristics of each type of printed circuit board, the recovery of precious metals may be the main goal of the recycling process of printed circuit boards from personal computers and the recovery of copper should be the main goal of the recycling process of printed circuit boards from mobile phones. Hence, these printed circuit boards would not be mixed prior treatment. The results of this paper show that copper concentration is increasing in mobile phones and remaining constant in personal computers.

Metal separation from mixed types of batteries using selective precipitation and liquid-liquid extraction techniques.

The purpose of this paper is to study metal separation from a sample composed of a mixture of the main types of spent household batteries, using a hydrometallurgical route, comparing selective precipitation and liquid-liquid extraction separation techniques. The preparation of the solution consisted of: grinding the waste of mixed batteries, reduction and volatile metals elimination using electric furnace and acid leaching. From this solution two different routes were studied: selective precipitation with sodium hydroxide and liquid-liquid extraction using Cyanex 272 [bis(2,4,4-trimethylpentyl) phosphoric acid] as extracting agent. The best results were obtained from liquid-liquid extraction in which Zn had a 99% extraction rate at pH 2.5. More than 95% Fe was extracted at pH 7.0, the same pH at which more than 90% Ce was extracted. About 88% Mn, Cr and Co was extracted at this pH. At pH 3.0, more than 85% Ni was extracted, and at pH 3.5 more than 80% of Cd and La was extracted.

Electronic scraps--recovering of valuable materials from parallel wire cables.

Every year, the number of discarded electro-electronic products is increasing. For this reason recycling is needed, to avoid wasting non-renewable natural resources. The objective of this work is to study the recycling of materials from parallel wire cable through unit operations of mineral processing. Parallel wire cables are basically composed of polymer and copper. The following unit operations were tested: grinding, size classification, dense medium separation, electrostatic separation, scrubbing, panning, and elutriation. It was observed that the operations used obtained copper and PVC concentrates with a low degree of cross contamination. It was concluded that total liberation of the materials was accomplished after grinding to less than 3 mm, using a cage mill. Separation using panning and elutriation presented the best results in terms of recovery and cross contamination.